上海龙凤交友论坛

Article publishing
Home page > Article publishing > Hangzhou plastic water tank wholesale

Hangzhou plastic water tank wholesale

Release time: 2023-02-19 01:15:53
 Hangzhou plastic water tank wholesale

Hangzhou plastic water tank wholesale

Plastic barrel modification equipment What are the processing equipment for plastics? Plastic barrel modification equipment Plastic modification involves four aspects: raw and auxiliary materials used, processing equipment, modification technology and effect, and specific application. According to the plastic modification process, the processing equipment can generally be divided into four categories: primary mixing, melt mixing, pelletizing and drying. The corresponding equipment is introduced as follows: primary mixing equipment. Primary mixing equipment refers to the equipment used for mixing materials in the non melting state. The equipment used for primary mixing is almost intermittent. There are many types of primary mixing equipment, such as rotary drum mixer, double cone mixer, spiral belt mixer, Z-shaped kneader high-speed mixer, etc., but at present, the two types of widely used plastic mixing processes are Z-shaped kneader and high-speed mixer. Z-shaped kneader Z-shaped kneader, also called double arm kneader, is mainly composed of rotor, mixing chamber and driving device. The rotor is installed in the mixing chamber. The mixing chamber is a steel trough with a W-shaped or saddle shaped bottom. The upper part is provided with a cover and a feeding port, and the lower part is generally provided with a discharge port. The steel trough is jacket type, and heating and cooling medium can be fed into it. Some high-precision mixing chambers are also equipped with vacuum devices, which can discharge moisture and volatile matter during the mixing process. There are two types of rotor installation in the mixing chamber, one is tangential installation and the other is intersecting installation. In tangential installation, the movement traces of the outer edges of the two rotors are tangent; In the intersecting installation, the movement traces of the outer edges of the two rotors are intersecting. During tangential installation, the rotor can rotate in the same direction or in different directions, and the speed ratio between rotors is 1.5:1, 2:1 or 3:1. The rotor installed in intersecting mode can only rotate at the same speed because the outer edge movement traces intersect. The clearance between the outer edge of the rotor installed in an intersecting manner and the wall of the mixing chamber is very small, generally about 1mm. In such a small gap, materials will be strongly sheared and squeezed. This effect can be physically modified by filling and blending.

 Hangzhou plastic water tank wholesale

Hangzhou plastic water tank wholesale

The advantages of chemical barrel! Chemical barrel is mainly composed of extrusion and blow molding, so it is generally called blow molding in the industry. The products produced by this process are made of plastic particles that pass through the hopper mouth, melt them through the heating of the cylinder in the three-stage heating zone, form them through the filter screen, clamp the parison into the petal closing mold to be blown when it is hot, blow it with compressed air, reach the mold cavity body, and open the petal closing mold after cooling and shaping under the condition of maintaining a certain time and air pressure, Then you can see the chemical barrel products. The volume of the oil tank of the chemical drum is too small, the heat dissipation area is not enough, and the capacity of the cooling device is too small. The high temperature of the climate and operating environment causes the rise of the oil temperature. The viscosity of the selected oil is not proper. The viscosity is large, and the resistance is large. If the viscosity is too small, the leakage will increase. Both conditions can generate heat and temperature rise

 Hangzhou plastic water tank wholesale

Hangzhou plastic water tank wholesale

Compared with previous years, this year is a miracle year, because there is no time comparable to this year. Just this year, our plastic buckets have made a new breakthrough, and we have made changes in quality! It has achieved what has been desired in recent years. At present, the plastic barrels of our factory have a long service life. Under the conditions of normal filling, transportation, loading and unloading, the warranty period is 18 months. The technical parameters of the plastic bucket are strictly in accordance with the specifications, and the appearance design and product dimensions of the plastic bucket can also be customized according to the needs. Plastic barrels can be used for hot filling, and the general temperature should not exceed 60 ℃. After hot filling, the lid and stacking shall not be closed until the contents have cooled sufficiently and dropped to room temperature.

 Hangzhou plastic water tank wholesale

Hangzhou plastic water tank wholesale

Although plastic buckets can be seen everywhere, do you know how they are packaged? What technology is there for packaging? 1. Plastic packaging barrel packaging: Fieldbus technology. The use of fieldbus technology has mainly "liberated" most of the hardware, simplifying the cumbersome device links; In the practical process of production and use, convenience and flexibility become more and more obvious; It can integrate fieldbus skills with the ERP system, so that the management can easily access and analyze operating data through the ERP system, understand the production practice and immediate situation, and monitor the operation of the workshop. Fieldbus technology is widely used in large food processing enterprises in China, which facilitates the unmanned operation of the entire production line and the seamless connection of transmission, detection and other processes. 2. Sensor plastic packaging barrel packaging technology. In the food processing and packaging machinery profession, the use of sensors is complex, and sensors are used in the monitoring of food and beverage storage tanks, filling and packaging, mixing and processing, cooling and heating, cleaning, packaging and other processes. The gap in the market for the use of this skill has become a must for many automation manufacturers. 3. Drive operated packaging barrel packaging technology. The use of transmission products in packaging machinery is mainly to adjust the main process speed and control the periodic change of motor speed in the production process. But for most packaging machinery, frequency converter is not a necessary electrical product. The application rate of frequency converter in this profession is low, and there is a large space for development in large standard machines and packaging production lines.