Nanyang plastic water tank manufacturer
The advantages of chemical barrel! Chemical barrel is mainly composed of extrusion and blow molding, so it is generally called blow molding in the industry. The products produced by this process are made of plastic particles that pass through the hopper mouth, melt them through the heating of the cylinder in the three-stage heating zone, form them through the filter screen, clamp the parison into the petal closing mold to be blown when it is hot, blow it with compressed air, reach the mold cavity body, and open the petal closing mold after cooling and shaping under the condition of maintaining a certain time and air pressure, Then you can see the chemical barrel products. The volume of the oil tank of the chemical drum is too small, the heat dissipation area is not enough, and the capacity of the cooling device is too small. The high temperature of the climate and operating environment causes the rise of the oil temperature. The viscosity of the selected oil is improper. The viscosity is large, and the resistance of viscosity is large. If the viscosity is too small, the leakage will increase. Both conditions can generate heat and temperature rise
Nanyang plastic water tank manufacturer
The plastic bucket for holding water is made of PE raw material, and its composition is attributed to linear low-density polyethylene particles. The plastic bucket made of this raw material is very healthy and environmentally friendly, and meets the national food safety standards. It not only has rigidity and resistance, but also has advantages such as high temperature and cold resistance. Generally speaking, plastic buckets have two purposes, one is to hold water, the other is to hold some corrosive liquids, so their choice of raw materials is different. Plastic buckets used to hold water should be environmentally friendly, green and healthy; The drums for storing corrosive liquids are required to be resistant to acid and alkali and corrosion. Plastic bucket is widely used in civil, agriculture and industry, and its scale of use can be classified as follows: 1. Civil: it is used to store and supplement at night (urban water consumption is low) because of drinking water supply problems, and it is used to make up for the overall water supply system when water consumption is serious; 2. Agriculture: when the rain is scarce, it is used to make up for the water content of farmland crops and drinking water for farm animals; 3. Industry: It is used to store industrial raw materials, and has ambitions for various acidic and alkaline industrial raw materials. Plastic buckets are ubiquitous in our lives. Because of their strong adaptability to the environment and high tear resistance, plastic buckets are loved by modern people, widely used in some factories, enterprises and individual families, and have been recognized and praised all the time.
Nanyang plastic water tank manufacturer
1： Measurement of the overall height of the plastic bucket. The overall height of the plastic bucket refers to the vertical distance from the bottle mouth to the bottom of the bottle. The measurement method is to place the plastic bucket on a horizontal plane, contact one end of the vernier caliper with the extreme high point of the bottle mouth, rotate the bottle body 360 degrees, read the maximum and minimum values respectively, and compare the data with the size of the design drawing to see whether they are consistent. If the specification of the plastic bucket is 40-60ml, its height should be controlled within ± 0.5mm. 2： Measurement of the outer diameter of the plastic bucket mouth. For the measurement of this part, the method is to span the scale of the measuring tool across the center of the bottle mouth, avoid the position of the mold closing line of the bottle body, rotate the circular bottle mouth 360 degrees with the main shaft close to the thread of the mouth, measure the maximum and minimum values, and compare with the bottle design drawings. The external diameter error should be controlled within ± 0.1mm. 3： Measurement of the overall diameter of the plastic bucket. For the measurement of this part, the method is to use the measuring surface of the vernier caliper to contact the measuring position of the maximum outer diameter of the bottle body, close the vernier caliper, rotate the plastic can body 360 degrees, and read the maximum and minimum values. The error of its overall diameter should be controlled within 0. 1mm. 4： Measurement of the wall thickness of each part of the plastic barrel. For the pharmaceutical plastic barrel with a circular revolving body, cut the measuring area of the symmetrical part with a knife, so that the measuring tool can enter the detection point where each part of the bottle can be measured. Strictly measure the symmetrical part of the thickness of the plastic barrel mouth, shoulder, body, and bottle bottom, and read the maximum and minimum values, Compare with the design drawing data, and check whether the tolerance of thickness dimensions of each part of the plastic bucket is within the standard range.
Nanyang plastic water tank manufacturer
Although plastic buckets can be seen everywhere, do you know how they are packaged? What technology is there for packaging? 1. Plastic packaging barrel packaging: Fieldbus technology. The use of fieldbus technology has mainly "liberated" most of the hardware, simplifying the cumbersome device links; In the practical process of production and use, convenience and flexibility become more and more obvious; It can integrate fieldbus skills with the ERP system, so that the management can easily access and analyze operating data through the ERP system, understand the production practice and immediate situation, and monitor the operation of the workshop. Fieldbus technology is widely used in large food processing enterprises in China, which facilitates the unmanned operation of the entire production line and the seamless connection of transmission, detection and other processes. 2. Sensor plastic packaging barrel packaging technology. In the food processing and packaging machinery profession, the use of sensors is complex, and sensors are used in the monitoring of food and beverage storage tanks, filling and packaging, mixing and processing, cooling and heating, cleaning, packaging and other processes. The gap in the market for the use of this skill has become a must for many automation manufacturers. 3. Drive operated packaging barrel packaging technology. The use of transmission products in packaging machinery is mainly to adjust the main process speed and control the periodic change of motor speed in the production process. But for most packaging machinery, frequency converter is not a necessary electrical product. The application rate of frequency converter in this profession is low, and there is a large space for development in large standard machines and packaging production lines.
Nanyang plastic water tank manufacturer
The volume of the plastic bucket oil tank is too small, the heat dissipation area is not enough, and the cooling device has too small capacity. The high temperature of climate and operating environment causes the oil temperature to rise. The viscosity of the selected oil is not appropriate, the viscosity is large, the viscosity resistance is large, and the leakage will increase if the viscosity is too small, both of which can cause heating temperature rise. The pipeline of the plastic bucket system is too thin and too long, too much bending, and large local pressure loss and pressure loss along the way. The precision of components is not enough and the assembly quality is poor, and the mechanical friction loss between relative motions is large. The fit clearance of the mating parts is too small, or the clearance is too large after use, resulting in large internal and external leakage, resulting in large volume loss. For example, the volume efficiency of the pump is reduced, and the temperature rises quickly. The constant displacement pump oil supply system of the plastic bucket with the oil pump capacity selected according to the fast forward speed will have most of the excess flow overflowing from the overflow valve under high pressure and generate heat during operation. The unloading circuit in the system fails or the oil pump cannot unload when it stops working because no unloading circuit is set. All flow of the pump overflows under high pressure, causing overflow loss and heating, resulting in temperature rise.
