Ningbo plastic water tank manufacturer
With the use rate of 200L large plastic barrels getting higher and higher, more and more old plastic barrels begin to appear gradually, including some plastic barrels that are broken during transportation, so we specially talk about how to repair the cracks on the plastic barrels. Now 200L plastic drums basically contract the transportation of chemical products, and the cost of plastic ton drums is also very high. If the old and damaged ton drums are replaced with new ones, the cost is too high. So let's talk about the repair of plastic buckets. Plastic buckets are indeed carriers for transporting chemical products, even dangerous plastic buckets, but they are not irreparable. The glue specially used to repair the plastic bucket is AB glue, which is composed of two kinds of glue liquids, one is hardener and the other is the glue. The combination of two liquids can achieve good bonding effect of zui, and the temperature must be appropriate. Although the use conditions are harsh, the bonding effect of the plastic bucket is extremely good. The 200L plastic bucket we usually use is always transported on the truck, and damage is inevitable during long-distance transportation. So many enterprises using plastic ton buckets will prepare sufficient AB glue.
Ningbo plastic water tank manufacturer
The plastic bucket for holding water is made of PE raw material, and its composition is attributed to linear low-density polyethylene particles. The plastic bucket made of this raw material is very healthy and environmentally friendly, and meets the national food safety standards. It not only has rigidity and resistance, but also has advantages such as high temperature and cold resistance. Generally speaking, plastic buckets have two purposes, one is to hold water, the other is to hold some corrosive liquids, so their choice of raw materials is different. Plastic buckets used to hold water should be environmentally friendly, green and healthy; The drums for storing corrosive liquids are required to be resistant to acid and alkali and corrosion. Plastic bucket is widely used in civil, agriculture and industry, and its scale of use can be classified as follows: 1. Civil: it is used to store and supplement at night (urban water consumption is low) because of drinking water supply problems, and it is used to make up for the overall water supply system when water consumption is serious; 2. Agriculture: when the rain is scarce, it is used to make up for the water content of farmland crops and drinking water for farm animals; 3. Industry: It is used to store industrial raw materials, and has ambitions for various acidic and alkaline industrial raw materials. Plastic buckets are ubiquitous in our lives. Because of their strong adaptability to the environment and high tear resistance, plastic buckets are loved by modern people, widely used in some factories, enterprises and individual families, and have been recognized and praised all the time.
Ningbo plastic water tank manufacturer
Why is the chemical barrel deformed? 1. In actual use, the chemical barrel will be deformed due to the great difference in the thickness of the barrel wall. However, the machines used to make chemical barrels in China are relatively backward, and there are fewer control points for wall thickness, which results in the asymmetry of the barrel body. Therefore, when formulating the standards for chemical barrels, they are also relatively loose. In some cases, the two relatively symmetrical wall thicknesses are about 2:1. The chemical barrel with uneven wall thickness is often judged as qualified when dissecting. 2. According to relevant people, the ambient temperature is the main factor causing the deformation of plastic chemical barrel. We should control the ambient temperature of plastic chemical barrel to prevent it from deformation. The plastic chemical barrel can carry a high heat of 108 degrees, and a low heat of 70 degrees below zero. Therefore, in general, the temperature of the liquid carried by the plastic chemical barrel should be 40 degrees below zero to 60 degrees below zero. If this value range is exceeded, when the chemical plastic bucket device weighs more or the temperature is higher, protective measures should be taken for the plastic chemical bucket to avoid deformation of the plastic chemical bucket. 3. After the chemical drum is filled with liquid goods, after the lid is tightly rotated, because it is airtight, when the liquid inside is cooled, the pressure inside the drum becomes smaller, while the external pressure is larger, forming the pressure difference between the surface and the inside of the drum, causing the deformation of the chemical drum. The inspection procedure for chemical drums clearly stipulates that they should be sealed and airtight. If the liquid inside is dangerous goods, the chemical drums for Class I dangerous goods should be able to accept a pressure of 30Kpa/cm2, and the plastic drums for Class II and III dangerous goods should also be able to accept a pressure of 20Kpa/cm2.
Ningbo plastic water tank manufacturer
What causes the temperature to be too high when processing plastic buckets? The reason for the high temperature during the processing of the plastic bucket: the volume of the plastic bucket oil tank is too small, the heat dissipation area is not enough, and the cooling device is too small. The high temperature of climate and operating environment causes the oil temperature to rise. The viscosity of the selected oil is not appropriate, the viscosity is large, the viscosity resistance is large, and the leakage will increase if the viscosity is too small, both of which can cause heating temperature rise. The pipeline of the plastic bucket system is too thin and too long, too much bending, and large local pressure loss and pressure loss along the way. The precision of components is not enough and the assembly quality is poor, and the mechanical friction loss between relative motions is large. The fit clearance of the mating parts is too small, or the clearance is too large after use, resulting in large internal and external leakage, resulting in large volume loss. For example, the volume efficiency of the pump is reduced, and the temperature rises quickly. The constant displacement pump oil supply system of the plastic bucket with the oil pump capacity selected according to the fast forward speed will have most of the excess flow flowing back from the overflow valve and generate heat when working. The unloading circuit in the system fails or the oil pump cannot unload when it stops working because no unloading circuit is set. All the flow of the pump overflows at the bottom, causing overflow loss and heating, resulting in temperature rise.
