Xianyang plastic water tank manufacturer
The grain size of the plastic in the plastic bucket is very harmful. The relativity of optical rotation is small or no optical rotation. The surface energy of the plastic bucket is low, which will harm the adhesion of all coatings. Because plastics are not conductive conductors and insulators in China, we cannot immediately carry out different coating on the surface of plastic barrels according to a set of electroplating process technical processing process design standards. Therefore, before the problem of information resource management on the surface of plastic barrels, it should be solved before social development, In order to better improve the bonding property of commercial coating and provide a conductive layer with excellent bonding property in coating solution. The front solution includes plastic product surface degreasing, vegetable oil cleaning, film remover, and active plastic product surface to improve coating adhesion. (1) Degrease the plastic bucket. Degreasing similar to metal manufacturing, and degreasing of plastic products can be cleaned with solvent or partial alkaline solution containing surface surfactant. Solvent degreasing is suitable for cleaning paraffin, liquid paraffin, body fat and other organic chemical stains on the surface. Commonly used solvents can not dissolve, solubilize or crack plastic products, with low melting point, easy volatilization, no toxicity, and nonflammable. Meta alkali solution is suitable for degreasing of alkali resistant plastic products. Because there are anhydrous aluminum chloride, meta alkali salt and chemical substances that carry out specific scientific research on different surfaces in this kind of standard solution. The common surface specific compounds are OP series products, namely alkyl carboxylic acid polyoxyethylene ether, which is not easy to develop into a foam plastic and does not remain on the surface of plastic products. (2) The activity of the surface of the plastic bucket. Some plastic barrels, such as polyethylene goods and ABS goods, can also be immediately coated on the surface of plastic barrels without organic chemical air oxidation. In order to better obtain high-quality coating coverage, air oxidation solution after degreasing can also be carried out for ABS products. Thin chromic acid solution diluent can be used. The typical solution secret is 420 g/L chromic acid and 200 ml/L hydrochloric acid (1.83%). The typical treatment is 65 ℃/five minutes and ten minutes, cleaning and drying. The advantages of chromic acid etching processing: the symmetrical solution of various and complicated plastic products; Defects of chromic acid etching process: actual operation risk.
Xianyang plastic water tank manufacturer
What causes the temperature to be too high when processing plastic buckets? The reason for the high temperature during the processing of the plastic bucket: the volume of the plastic bucket oil tank is too small, the heat dissipation area is not enough, and the cooling device is too small. The high temperature of climate and operating environment causes the oil temperature to rise. The viscosity of the selected oil is not appropriate, the viscosity is large, the viscosity resistance is large, and the leakage will increase if the viscosity is too small, both of which can cause heating temperature rise. The pipeline of the plastic bucket system is too thin and too long, too much bending, and large local pressure loss and pressure loss along the way. The precision of components is not enough and the assembly quality is poor, and the mechanical friction loss between relative motions is large. The fit clearance of the mating parts is too small, or the clearance is too large after use, resulting in large internal and external leakage, resulting in large volume loss. For example, the volume efficiency of the pump is reduced, and the temperature rises quickly. The constant displacement pump oil supply system of the plastic bucket with the oil pump capacity selected according to the fast forward speed will have most of the excess flow flowing back from the overflow valve and generate heat when working. The unloading circuit in the system fails or the oil pump cannot unload when it stops working because no unloading circuit is set. All the flow of the pump overflows at the bottom, causing overflow loss and heating, resulting in temperature rise.
Xianyang plastic water tank manufacturer
First, check whether the lid and barrel body of the plastic barrel are matched products when filling, otherwise, if the lid and barrel body are not matched, the liquid may leak from the mouth. Liquid temperature shall not be higher than 70 ℃. The storage should be dark, the temperature should be below 40 ℃, and the temperature should not exceed 25 ℃ when loading and transporting. Do not load and transport the plastic packaging barrel immediately after filling the high-temperature liquid. Please do not drag the chemical barrel directly on the ground during the transportation of the filled liquid to avoid abrasion and bruise at the bottom. The correct method is to lift it with both hands or use a forklift wooden pallet for shipment.
Xianyang plastic water tank manufacturer
The forming time of the barrel has a great impact on the size of the mold! Plastic part structure The shape, size, wall thickness, presence or absence of inserts, the number and distribution of inserts have a great impact on the shrinkage. Generally speaking, plastic parts are complex in shape, small in size, thin in wall, with inserts, a large number of inserts and symmetrical distribution, and their shrinkage is small. The cooling and shaping process starts from the freezing of the gate to the demoulding of the product, which is a stage of the injection molding process. At this stage, feeding or backflow will not continue, and the plastics in the cavity will continue to cool, harden and shape. When demoulding, the plastic parts have enough rigidity to avoid warping and deformation. As the cooling process proceeds, the temperature continues to drop, and the plastic shrinkage pressure in the cavity drops to a lower value (but not necessarily equal to the outside atmospheric pressure) when the mold is opened.
