Guiyang plastic water tank manufacturer
Briefly describe the repair method of the damaged packaging barrel: first remove the external dirt on the damaged part of the packaging barrel, first wipe off the dirt with a rag, and then scrape out new debris with a knife. If there is any oil stain, first use hot alkaline water to remove the oil, then wash the alkaline solution with clean water, and then use a knife to scrape the surface. When patching cracks, it is necessary to cut a plastic sheet of the same type that is slightly longer and wider than the crack, and has no aging, and treat the appearance. Then, at the place where the packaging barrel is broken, all of them are glued in order, and wet cloth is used to press them to make the bonding more tight. The packaging barrel is beautiful in appearance, smooth in appearance, seamless in appearance, light in weight, good in strength, impact resistant, non-toxic and tasteless, convenient in transportation, and has a long service life. Under the conditions of normal filling, transportation, loading and unloading, the warranty period is 1.5 years. The technical parameters of the product should strictly comply with the standards, and the product appearance design and product dimensions can also be customized according to the needs. Hot filling can be used, and the general temperature should not exceed 60 ℃. The lid and stacking shall not be closed until the contents have cooled sufficiently and dropped to room temperature. Chemical packaging barrels are mostly made of plastic, commonly known as plastic chemical barrels or plastic chemical barrels. They are developed and blown with scientific formulas. They are beautiful and generous in appearance, prevent leakage, and will not deform. They are ideal for long-distance transportation of packaging materials for chemical products. The chemical packaging barrel has good anti-corrosion performance, and a variety of raw material "O" type sealing rings are selected to meet different filling requirements. The residual amount after dumping is small, and it can be used more than 20 times under normal filling, transportation and loading and unloading conditions. It not only saves energy but also reduces the cost of use.
Guiyang plastic water tank manufacturer
Let me share with you the advantages of using plastic buckets! In terms of convenient use of plastic buckets, the first is the plastic buckets with small capacity and light packaging weight. The main body of this kind of plastic bucket packaging is the function scheme of the handle. It is an important part of the demand thinking of the plastic bucket scheme to make the handle more labor-saving and convenient to use. There is a need for more thoughtful ideas about large capacity plastic buckets. For example, some large plastic waste barrels loaded with wheels are very convenient to push, pull and use. The second is the use of plastic buckets. Plastic barrels are usually quoted at a higher price, and they have been used. For example, many migrant workers use paint plastic buckets to hold clothes, rice and pickles. From the perspective of convenient use, we think that it is necessary to think about convenient cleaning and disinfection of plastic buckets. After all, the recycling rate of plastic drums is also a demand driven direction. Nowadays, recycling of plastic drums is very low. The recycling of plastic bottles involves recovery, equipment and other aspects, and the demand is promoted step by step.
Guiyang plastic water tank manufacturer
First, the outer cover needs to be tightened when installing (usually with the help of external force such as wrench). After the installation of the seal ring, it should be close to the contact plane of the barrel mouth to prevent the seal ring from distorting the installation. If the temperature of the filled product is higher than 40 ℃, the cap shall be screwed and stacked after the product is cooled. When stacking, pay attention to ensure the flatness. The upper base layer with large contact area shall be aligned, and the stacking shall not be staggered to avoid deformation of the plastic bucket. The weight or specific gravity of the dangerous goods contained in the chemical barrel shall not exceed the larger weight or specific gravity of the contents that can be carried. It is not allowed to use plastic drums with low hazard class to pack dangerous goods in places where high hazard class packaging is required. If the plastic drum without vent hole is used for shipment, it will release gas during storage and transportation. The single weight or volume of dangerous goods contained in the barrel shall not exceed the high limit of the world rules for dangerous goods transportation. During loading, unloading and transportation, it is necessary to avoid falling and collision with hard and sharp objects. When loading dangerous goods, do not corrode or damage the appearance of the plastic barrel.
Guiyang plastic water tank manufacturer
Compared with previous years, this year is a miracle year, because there is no time comparable to this year. Just this year, our plastic buckets have made a new breakthrough, and we have made changes in quality! It has achieved what has been desired in recent years. At present, the plastic barrels of our factory have a long service life. Under the conditions of normal filling, transportation, loading and unloading, the warranty period is 18 months. The technical parameters of the plastic bucket are strictly in accordance with the specifications, and the appearance design and product dimensions of the plastic bucket can also be customized according to the needs. Plastic barrels can be used for hot filling, and the general temperature should not exceed 60 ℃. After hot filling, the lid and stacking shall not be closed until the contents have cooled sufficiently and dropped to room temperature.
Guiyang plastic water tank manufacturer
How to deal with the liquid container after use? The used liquid packaging barrels are not allowed to be thrown randomly, and must be disposed properly, otherwise it will cause environmental pollution. Pay attention to the following points when handling: 1. First, ensure that the vehicles transporting liquid packaging barrels are in good condition. 2. Construction waste: waste oil drums, waste paint drums, waste fire extinguisher cans, waste plastic cloth, waste chemical materials and their packaging materials, waste glass fiber cloth, etc., shall be disposed according to relevant regulations, and shall not be discharged at will, otherwise serious harm will be caused. 3. Try to recycle the waste and do not cause secondary pollution. According to the requirements of relevant national laws and regulations, the waste paint bucket in the liquid packaging bucket belongs to hazardous waste. Recycling can only be done by a qualified waste disposal company. However, there are a large number of waste paint buckets, each of which is 1.5kg-2k. If hazardous waste is treated, a lot of treatment costs will be incurred.
